When a line lets go behind drywall, every minute adds gallons to the damage. Close the main valve, call Water Heater Repairer, and a real person will connect you with a licensed and insured independent plumber close by, and a drying contractor if the water spread.
A burst pipe is two jobs at once: stopping the leak and dealing with the water it already dumped. We line up both trades so you are not making five calls while water keeps moving.
Repairs to supply lines fall under plumbing code, which is why we route only to licensed, insured independent plumbers. Feel free to ask for their license at the door and verify it yourself.
We triage by severity, so active spray and sagging ceilings move to the front of the line. Response is typically fast, though a hard freeze can stretch every schedule in town.
The plumber explains what has to open up and writes a flat-rate price before cutting drywall. No surprise line items once the wall is open.
Plenty of the plumbers we route to bring acoustic listening gear and a thermal camera. That narrows the break down to inches instead of tearing out a whole wall to hunt for it.
Split copper, popped PEX fittings, brittle CPVC, and leaks under the slab are all daily calls here. Describe the pipe and where it is, and we connect you with a plumber who handles that exact material all the time.
When water has already soaked drywall, insulation, or subfloor, fixing the pipe is only half the job. We can route a water damage contractor who brings moisture meters, air movers, and dehumidifiers so the framing dries before anything gets closed up. Closing a wet wall is how small leaks turn into mold calls months later.
Pipe material, location, and the reason it broke decide which repair makes sense.
Pipes running through outside walls, vented crawlspaces, and attics are the first to freeze. Ice expands, pressure builds between the blockage and a closed faucet, and the pipe splits lengthwise, often hours later when it thaws.
Type M copper has a thinner wall than Type L, so it tends to split and pinhole sooner. The plumber cuts back to sound pipe and sweats or press-fits a permanent repair.
PEX itself flexes, yet the crimp rings and expansion fittings are where freeze damage shows up. Aging CPVC gets glass-brittle, so a cracked elbow often means nearby joints are close to failing too.
A hot spot on the floor or a meter that spins with every tap closed points to a slab leak. The plumber locates it with listening gear and a thermal camera, then lays out spot repair versus a reroute.
Old galvanized pipe corrodes from inside out, and the threads are usually where it gives up. Patching one section of a rotted run often just moves the leak a few feet down the line.
Braided supply hoses on toilets, faucets, and washers can rupture at full line pressure with no warning. A relief valve on the water heater that drips or dumps water needs a look too.
The process is short, and a real person handles each part.
We walk you through finding the main shutoff and killing power to any wet circuits. Then we ask what the pipe is made of, where it runs, and whether a ceiling is bulging.
We route the job to a nearby licensed plumber who carries stock for copper, PEX, and CPVC repairs. If water spread past the leak area, a water damage contractor can be scheduled right behind them.
The pro locates the split, looks over the rest of the line, and notes any pinholes or brittle fittings nearby. You get a written flat-rate quote before any wall gets opened.
After the repair, the system is repressurized and tested, and joints are checked dry before the wall goes back. Ask about the contractor's own written workmanship warranty before they leave.
Push-to-connect fittings are great at two in the morning because they go on wet and stop the water fast. Many plumbers still prefer a sweated or press fitting behind drywall, since that joint will sit unseen for decades.
Shut the main and call. We will get a licensed plumber moving your way.
A pipe in the outside wall of our laundry room froze and split during the first cold snap. The dispatcher talked me through finding the main, and the plumber replaced the split copper that same morning. He even pointed out that it was thin Type M and why that mattered.
Our water bill doubled and the hallway tile felt warm. The plumber used a listening device and a thermal camera and found the slab leak in about twenty minutes. He gave us a written price for a spot repair and another for rerouting through the attic, and let us pick.
Water came through the dining room ceiling from an upstairs bathroom supply line. The plumber fixed the line and a water damage contractor showed up after to dry the ceiling and floor. Having both lined up from one call saved me a long night of searching.
I manage a small rental, and a tenant called about a CPVC elbow that cracked under the kitchen sink. The plumber replaced it, then showed me two more fittings that crumbled when he touched them. He quoted a full repipe of that wall in writing and did not pressure me to do it that day.
Close the main shutoff right away and kill power to wet areas at the panel. Drain the system by opening a low faucet, pull belongings out of the path, and call for a plumber.
Open the faucet the pipe feeds and warm the section slowly with a hair dryer, heat lamp, or space heater. Skip the torch entirely, because open flame starts wall fires and can burst the pipe with steam.
They are code-approved in many places, yet a lot of plumbers prefer them only where they stay accessible. Have the plumber explain whether a sweated or press joint is the better long-term choice.
Acoustic leak detectors pick up the hiss of escaping water, and thermal imaging shows cool or warm patches where it spreads. Together they usually narrow the access hole to a small, patchable opening.
One leak on otherwise healthy pipe is usually a good case for a spot repair. Repeated leaks or aging copper tend to point toward a reroute so you are not breaking concrete again next year.
Drip faucets on exterior walls during deep cold and leave cabinet doors open for heat. Insulate exposed runs and add heat tape where pipes pass through cold crawlspaces, starting with the spots the plumber flags.
Calls go to independent plumbers covering Austin, from older homes with galvanized pipe to new construction running PEX. Surrounding suburbs are part of the coverage, including zip codes like 55912.
Older homes near the center of town tend to have galvanized mains and thin copper branch lines, which is where pinhole leaks and corroded threads show up. Newer subdivisions lean on PEX and CPVC, where freeze-popped fittings and brittle elbows are the usual story. Give the dispatcher a rough age for the house and we route someone who knows that era of plumbing.
Frozen crawlspace pipes, attic runs, and slab leaks across older and newer houses.
Shared-wall leaks where stopping the water fast and documenting it for the association both count.
The same contractor network reaches the suburbs around Austin.
